6550 Van Buren Blvd, 1st Floor Ste D, Riverside, CA 92503Mon–Sat, 7am–6pm
Free in-home templating & quoteCall (951) 589-3336
Countertop Replacement in Riverside, CA by Riverside Custom Countertops

Service · Riverside, CA

Countertop Replacement in Riverside, CA That Ends the Patch-and-Hope Cycle

Riverside Custom Countertops handles countertop replacement in Riverside, CA for kitchens, baths and light commercial spaces. We swap failing tops for granite, engineered quartz, quartzite, butcher block, solid surface, porcelain and laminate, and we also do bathroom vanity tops, outdoor kitchen surfaces, sealing and polishing, and straight countertop repair when repair is still the smarter call.

Crews run daily across Riverside County, from Canyon Crest and Orangecrest to Arlanza and La Sierra, and out along Magnolia Avenue and Arlington Avenue toward the 91.

Free estimate

Get your free written quote

Send your details and we reply the same business day. No obligation, and the estimate is in writing.

Or call (951) 589-3336 — calls only, we don't receive text messages.

Thanks, we have your request.

We reply the same business day, Monday through Saturday. For same-day scheduling call (951) 589-3336.

Free written estimate

Digital templating

Cut in our Riverside shop

Licensed & insured

01

Signs Your Countertop Is Past Repair

Repair buys time. These six failures do not respond to it.

Laminate delamination. Once the sheet lifts off the particle board or MDF substrate, the bond is gone. Re-gluing a lifted edge near a sink fails again fast, since the core has already swelled.

Knife scarring that cannot be disinfected. Heavy knife scarring in laminate cannot be sanitized. That is a food-safety problem, not a cosmetic one. Wood differs, since bacteria are absorbed into the grain but do not multiply, so scarred butcher block is usually refinishable.

Deep staining in unsealed stone. Natural stone has poor primary permeability but strong secondary permeability through cracks. Once sealing lapses past the five to ten year window an oleophobic impregnator buys you, oil and acid run down the fissures where honing cannot reach.

Cracked seams. A seam that has opened and moved says the substrate or the cabinet run underneath has shifted. Refilling it treats the symptom.

Impact damage in solid surface. Solid surface has lower impact resistance than stainless or cast iron and moves at temperature extremes. Small chips sand out. A spidered area under a dropped pot does not sand out.

Thermal cracking in quartz. Engineered quartz resists heat below roughly 150 degrees Celsius but cracks under sudden temperature change. A crack crossing a cooktop cutout is a replacement.

02

Repair or Replace: How We Decide

ConditionTypical callInvestment level
Chip, small burn, dull finishRepair and refinishLower
Delaminated laminate near a sinkReplaceMid
Deep stain in unsealed stoneReplaceMid to higher
Thermal crack across a quartz cutoutReplaceHigher
Sagging cabinet run under stoneReplace after cabinet repairHigher

That call goes in writing before anything is torn out.

Countertop fabrication shop in Riverside, CA

03

Tear-Out and Disposal

Old tops come off in planned pieces, not with a pry bar. Stone gets cut down before lifting, because a 3cm slab section is heavy through a galley or down a stair. We shut off water, isolate the cooktop circuit, and score the caulk and adhesive lines so drywall paper stays put. Debris leaves the same day, and disposal is a real line on your quote, since stone, substrate and old sinks go to different places.

04

Protecting Your Cabinets During Removal

Most damage in a swap happens in the first hour. We tape and pad cabinet faces, cover the flooring on the path out, and back sink clips and screws out by hand instead of shearing them. Where the old top is glued to the rails, we cut the adhesive line instead of lifting the rail out with it.

05

Can Your Cabinets Carry a Stone Slab?

This is the question that gets skipped. Granite runs 2.65 to 2.75 grams per cubic centimeter, and slabs come in 2cm and 3cm. Before templating we check that boxes are level, rails are sound, and the run sits at the standard 35 to 36 inches off the floor with a proper toe kick. Older kitchens in Northside and Casa Blanca often need shims or a plywood deck, and overhangs need corbel or steel support.

06

Plumbing, Cooktop and Sink Reconnect

Faucets, disposals, dishwasher air gaps, drop-in ranges and cooktops come off before removal and go back after the new top is set and the silicone cures. Undermount sinks need a finished edge and a silicone bed. Drop-ins clamp from below against sealant. Stainless integrated sinks arrive welded and ground into the top. We tell you which nights the sink is out.

07

Template to Install Timeline

Digital templating produces dxf files, and slab photography lets you approve a multi-slab layout before a saw runs. Sink and cooktop details are pre-machined in the shop. Most stone jobs follow one rhythm: measure and quote, tear-out and template, fabrication, then install and reconnect. Solid surface is built in the shop and assembled on site with glued, sanded joints. Cast-in-place concrete needs cure time, and laminate turns around fastest.

08

Matching the New Top to Your Backsplash and Flooring

If the tile backsplash is staying, edge thickness matters. Going from a post-formed laminate top with a coved upstand to a flat 3cm stone edge leaves a gap where the cove was, so we plan a matching band or a tile course. An applied backsplash keeps spills out from behind the cabinets, so keep it. We also check the slab against your floor in daylight, because travertine and cool gray quartz can fight under LED light.

09

What Moves the Price of a Countertop Replacement

Your quote is driven by material and slab count, edge profile (a bullnose is simpler than an ogee), seam count, sink and cooktop cutouts, tear-out and disposal, backsplash work, plumbing reconnect, overhang support, and delivery or stair access. Fancier edges cost more. We quote options at more than one investment level instead of pushing the top of the range.

11

Service Areas

13

Why Riverside Homeowners Hire Us

Riverside Custom Countertops is licensed and insured. Our shop uses the wet cutting, local exhaust ventilation and respiratory protection controls California's emergency silica regulations require. The state counted 500 silicosis cases among fabrication workers as of January 2026, with 72 percent of shops out of compliance.

Questions

Frequently Asked Questions

Or call us on (951) 589-3336. Calls only — we do not receive text messages.

Should I repair or replace my countertop?

Repair chips, dull finishes and stable seams. Replace delaminated laminate, deeply stained unsealed stone, cracked quartz and any top on a failing cabinet run.

Do you haul away the old countertop?

Yes. Tear-out and disposal appear as a stated line on your quote, and debris leaves the same day.

Can my cabinets hold granite or quartz?

Usually, once we confirm the boxes are level and the rails are sound. We inspect before templating and add decking, shims or corbel support where needed.

How long will I be without a kitchen sink?

The sink and faucet come out at tear-out and go back once the new top is set and sealed. We give you the exact nights in advance.

Do I have to replace my backsplash too?

Not always. It depends on the old edge profile and how much wall the previous top covered. We flag it at the quote, not on install day.

Do you serve my ZIP code?

We cover 92501 through 92509 and 92513 through 92522, plus Corona, Eastvale, Norco, Redlands and the rest of the Inland Empire.

Free quote

Get Your Free Countertop Replacement Quote

Stop patching a top that is finished. Call Riverside Custom Countertops at (951) 589-3336 or visit 6550 Van Buren Blvd, 1st Floor Ste D, Riverside, CA 92503 for a free measurement and a written quote covering material, tear-out, disposal, plumbing reconnect and install dates. We answer, we show up, and we put it in writing.

  • Same business day response, Mon–Sat 7am–6pm.
  • No obligation — templating and the written quote are free.
  • You speak to the fabricator, not a call centre.

Request your quote

Name, number, and what you need.

Or call (951) 589-3336 — calls only, we don't receive text messages.

Thanks, we have your request.

We reply the same business day, Monday through Saturday. For same-day scheduling call (951) 589-3336.

Call (951) 589-3336